Waste Management Business
10-minute walkaround targets landfill and transfer-station fire risks
A 10- to 15-minute daily machine walkaround can catch wrapped debris, fluid leaks and fire risks before operators start work at landfills and transfer stations.

Waypoints
Proper walkarounds take 10 to 15 minutes at the start of every shift.
Paper, fines and dust packing beside hot exhaust are among the most common causes of equipment fires at solid waste facilities.
The inspection form must be completed daily and submitted immediately under company policy.
Access checks target three points of contact when operators climb on and off the machine.
Layne has more than 30 years of heavy-equipment safety experience, including 17 years at Caterpillar Inc.
By Elena Vasquez
A proper machine walkaround takes 10 to 15 minutes at the start of every shift, according to PurposeFirst founder Clay Layne, giving landfill and transfer-station crews a physical check against fires, breakdowns and injuries before equipment starts work.
“The walkaround is the simplest safety tool we have. It needs no special equipment, only time and attention,” Layne wrote.
Layne brings more than 30 years of experience in heavy-equipment operations and safety, including 17 years at Caterpillar Inc. He worked alongside research and development engineers and led operator training focused on best practices and safety in the waste industry.
His stated mission is to make the industry safer for frontline workers through leadership, education and accountability. His proposed daily window occupies less than 3% of the 10-hour day he describes on the working face, while targeting failures that can sideline a machine or turn smoldering debris into a fire.
Why does waste change the risk?
Waste equipment does not fail like construction equipment, Layne says, because the material stream attacks components quietly over a shift.
Wire, strapping, cable, carpet and plastic film wrap around axles, drivelines and track rollers. Paper, fines and dust pack into engine compartments and belly pans next to hot exhaust parts, a combination Layne identifies as one of the most common causes of equipment fires at solid waste facilities.
Rebar and scrap metal can force through guarding or doors into the engine compartment. Wood and other debris can become projectiles that break equipment windows, while dust clogs radiators and air filters until engines overheat.
Landfills add steep slopes, soft ground, mud and leachate that eats away at metal. Transfer stations add tight quarters, push walls, constant backing and pedestrians on the tipping floor. At sites that share machines between shifts, an incoming operator may not know what happened overnight.
What does a proper walkaround cover?
Operators should park the machine on level ground, lower its attachments and set the parking brake before starting. They must complete the inspection form daily and submit it immediately under company policy.
Layne calls the walkaround “a safety device, and it only works if we use it the right way,” rather than paperwork. The check follows a fixed sequence:
- Approach: Inspect the ground under and around the machine for fresh fluid spots, debris and anyone working nearby.
- Wrap and buildup: Check axles, drivelines, tracks and rollers for wrapped material. Open engine compartments and belly pans, clear packed debris near exhaust parts and turbochargers, and clean it out before startup.
- Fluids and leaks: Check engine oil, coolant, hydraulic fluid and fuel. Look for wet hoses, weeping fittings and damaged hydraulic cylinders.
- Tires, tracks and wheels: Look for cuts, punctures, low pressure, missing compactor cleats and loose track pads.
- Structure and attachments: Inspect pins, bushings, cutting edges, the bucket or blade, and the ROPS/FOPS for cracks or damage.
- Access: Make sure steps and handrails remain solid and clean so operators can keep three points of contact when climbing on and off.
- Visibility and warnings: Clean windows, mirrors and cameras. Confirm that lights, the horn and the backup alarm work.
- Fire protection: Verify that the extinguisher is charged and that the fire suppression system, if fitted, shows ready.
- After startup: Fasten the seat belt, check gauges and warning lights, and test the brakes and steering before moving.
Why do shortcuts persist?
Familiarity can turn the inspection into pencil whipping the walk around: a quick glance on the way to the cab, followed by a checklist marked the same way as the day before. Layne identifies three rationalizations: the machine was fine yesterday, the night shift would have reported a problem, or the defect can wait until greasing.
Completing forms in the break room or inspecting only the side facing the parking lot leaves real condition unchecked. A slow leak, weak backup alarm or wobbly step may look minor at shift start, but Layne says those faults matter at the end of a 10-hour day on the working face.
What must supervisors fix?
Physical verification means operators touch each item, open the doors they should look behind and record what they find. A checklist with the same marks every day for a month signals a warning, not proof of a sound machine, according to Layne.
Give every operator clear authority to tag out a machine they believe is unsafe, without requiring an argument. Supervisors should also walk around machines with operators occasionally, show that the inspection matters and coach newer workers on what to inspect.
Schedules set the standard. If managers expect loaders, compactors, dozers, excavators and articulated trucks to move the minute the gate opens, crews will rush the check. Layne advises building the 10- to 15-minute window into every shift and protecting it.
The maintenance response determines whether reporting continues. Record the defect, its date and the repair, then tell the operator it has been fixed. If a reported leaking hose still leaks a week later, Layne says operators will stop writing up problems.
Where does the payoff show up?
Those records do more than satisfy an auditor. They reveal which machines develop repeat problems, cut costly breakdowns and help keep fires off the tipping floor and working face. The routine can also prolong machine life and reduce maintenance costs, Layne says.
That payoff depends on operators, supervisors and the maintenance team working together and communicating repair status frequently. Without that loop, Layne says friction develops between the field team and maintenance.
For site operators, the next milestone is a closed repair loop: the defect logged and dated, the repair completed, and the operator told it has been fixed. A signed form alone does not close it.
via wasteadvantagemag.com (Source)
More from Elena Vasquez
Show full bio
Senior reporter covering technology and product news in Circular economy and the environmental industry at Circular Wire.
551 articles