Industrial Decarbonization
DMEGC Swaps Aluminum for Steel in 665 W Bifacial Module Push
DMEGC's Infinity RT 3.0 series runs 640-665 W on steel frames with near-double aluminum's tensile strength, 76% less rear shading and an 88.85% power guarantee at 30 years.

Waypoints
Infinity RT 3.0 series spans six models at 640-665 W with 23.7-24.6% efficiency
Zn-Al-Mg steel frames carry snow loads up to 6,000 Pa and wind loads up to 5,000 Pa
S-shaped frame cuts rear-side vertical shading by 76% and lifts theoretical bifaciality ~2.8%
Warranty: 15-year product, 30-year power, 88.85% output guaranteed at year 30
Simulated annual yield of 2,078 kWh/kWp, a 0.6% revenue gain vs conventional modules
Chinese solar manufacturer DMEGC has launched a six-module series, the Infinity RT 3.0, with power outputs of 640 W to 665 W and efficiencies between 23.7% and 24.6% — built on bifacial glass-glass modules framed not in aluminum but in zinc-aluminum-magnesium (Zn-Al-Mg) coated steel.
For an industry that has framed virtually every mainstream module in aluminum for decades, the material swap is the story. DMEGC says the steel frame has nearly twice the tensile strength of conventional aluminum alloys, which lets the modules withstand snow loads of up to 6,000 Pa and wind loads of up to 5,000 Pa when installed with suitable mounting systems.
"The zinc-aluminum-magnesium (Zn-Al-Mg) coated steel used in the frames has nearly twice the tensile strength of conventional aluminum alloys, enabling the modules to withstand snow loads of up to 6,000 Pa and wind loads of up to 5,000 Pa when installed with suitable mounting systems," a DMEGC spokesperson told pv magazine.
In plain terms: the company is betting that a cheaper, stronger frame metal can solve two problems at once — mechanical stress and rear-side yield losses.
Why steel framing changes the mechanics
DMEGC says the Zn-Al-Mg steel also has a lower coefficient of thermal expansion than aluminum or glass. That matters because steel and glass expand and contract at closer rates, and the company argues this reduces mechanical stress on the cells during temperature swings — specifically cutting the risk of cell microcracks, one of the quiet killers of long-term module performance.
The frame's geometry does its own work. An S-shaped cross-section reportedly cuts vertical shading on the rear side of the module by 76% compared with conventional frame designs. DMEGC said the shape increases the unshaded rear-side area by 3.6%, which works out to a theoretical bifaciality improvement of roughly 2.8%.
That's a material gain in a market where every tenth of a percent of rear-side yield counts toward project-level economics. Takeaway: the frame is no longer just structural — it's an active contributor to energy harvest.
What's inside the Infinity RT 3.0?
The DMxxxG12RT-B66HSW 640~665W models are built on 132 n-type monocrystalline half-cut cells. The physical spec sheet:
- Dimensions: 2,382 mm × 1,134 mm × 30 mm
- Weight: 33.3 kg
- Glass: 2 mm heat-strengthened glass on both sides
- Target segment: utility-scale PV
DMEGC rates the modules at a bifaciality factor of up to 85%. The company's own energy yield simulations point to annual electricity generation of 2,078 kWh/kWp, which it says corresponds to a 0.6% increase in generation revenue versus conventional modules under the simulated conditions.
Operating envelope and durability testing
The electrical and thermal ratings read like a standard utility-scale datasheet, with one or two numbers standing out:
- Maximum system voltage: 1,500 V
- Operating temperature range: -40 C to 85 C
- Temperature coefficient: -0.28%/C
- Nominal module operating temperature: 42 C
On durability, DMEGC said the products have undergone salt mist and ammonia corrosion testing — relevant for coastal and agricultural installations — plus extended stress testing. The steel frame's corrosion story rides on the Zn-Al-Mg coating, a treatment already used in aggressive-environment construction steel.
Warranty terms set the 30-year benchmark
The commercial guarantee is where DMEGC puts numbers behind the durability claims. The manufacturer offers a 15-year product warranty and a 30-year linear power output warranty, with degradation capped as follows:
- No more than 1% degradation in the first year
- A maximum annual degradation rate of 0.35% thereafter
- A guaranteed power output of 88.85% after 30 years
Those figures put the series in line with the front rank of n-type module warranties currently on the market. The takeaway: DMEGC is underwriting the steel-frame design for three decades, not just certifying it in a lab.
What to watch next
The announcement is a product launch, not a commissioned fleet — these are catalog specifications and company simulations, not third-party field data. DMEGC, which last November energized a 940 MW solar fishery project, has the utility-scale track record to place the series, but the open questions are independent yield verification and how the S-frame's simulated 2.8% bifaciality gain holds up across real albedo conditions.
The milestone that decides what happens next is market adoption: whether steel-framed modules land in bankable utility-scale projects and whether the 88.85% at-30-years guarantee survives contact with independent testing.
via pv-magazine-australia.com (Source)
More from Daniel Okafor
Show full bio
Correspondent covering companies, deals and strategy in Circular economy and the environmental industry at Circular Wire.
528 articles