Plastics & Chemical Recycling
EPSRC and Defra Put £1.7 Million Behind Bath's Acrylic Depolymerisation Scale-Up
EPSRC and Defra have granted Bath £1.7 million to scale UV-driven acrylic depolymerisation, targeting over 99% pure MMA monomer at 120–180°C by late 2029.

Waypoints
£1.7 million joint EPSRC–Defra grant announced 20 November 2026; EPSRC funds 80% (£1.36 million) under fEC
Bath process depolymerises PMMA at 120–180°C, versus 350–400°C for pyrolysis, recovering monomer above 99% purity
36-month programme through late 2029; pilot target of 100 g/h continuous throughput and 98% solvent recovery
Builds on chlorine-free depolymerisation published in Nature Communications in early 2026
UK acrylic recycling rates currently sit near zero
UK Research and Innovation announced on 20 November 2026 a £1.7 million joint grant to the University of Bath, charged with turning a laboratory photochemical depolymerisation process for acrylic plastics into a continuous pilot operation. The Engineering and Physical Sciences Research Council funds 80% of eligible costs — about £1.36 million under full economic costing — with Defra co-sponsoring and the university underwriting the remainder. The grant runs 36 months, through late 2029.
The target material is polymethyl methacrylate, the transparent resin sold as Perspex, Plexiglas and Lucite and used in automotive glazing, medical diagnostic equipment, architecture and digital displays. UK recycling rates for acrylics sit near zero. Mechanical remelting degrades PMMA, shearing chains until yellowing, haze and embrittlement disqualify the output from optical specifications. Commercial chemical recycling has relied on pyrolysis at 350–400°C, an energy-hungry route that produces char and has historically depended on hazardous halogenated reagents.
What does the Bath process change?
The Bath route unzips solid acrylic chains back into methyl methacrylate monomer at 120–180°C, in an oxygen-free solvent environment, triggered by ultraviolet light and an earth-abundant catalyst. It requires no chlorine-based solvents. The recovered liquid monomer exceeds 99% purity, permitting repeated repolymerisation without optical downcycling. The engineering trade-offs:
- Mechanical remelting: 200–250°C, downcycled output, cannot produce virgin optical sheet
- Thermal pyrolysis: 350–400°C, high energy, variable-purity monomer needing redistillation, emissions and char fouling
- Bath UV photodepolymerisation: 120–180°C, low energy intensity, virgin-grade monomer above 99%, but requires controlled UV flux and feed dissolution
Whether the economics beat virgin petrochemical monomer remains an open question; the team says rigorous techno-economic analysis across early pilot operations will decide it.
Who is running it?
The consortium sits within Bath's Institute of Sustainability and Climate Change. Dr Simon Freakley leads, with ISCC Research Fellow Dr Jon Husband, co-investigators Dr Sanjay Nagarajan and Dr Sam Cooper, and strategic advice from Professor Matthew Davidson, director of the Innovation Centre for Applied Sustainable Technologies. The programme spans the chemistry, chemical engineering and mechanical engineering departments and has recruited two postdoctoral researchers and one doctoral student to execute continuous reactor scale-up.
The grant builds on proof-of-concept work published in Nature Communications in early 2026, in which Husband and Freakley demonstrated chlorine-free chemical unzipping in greener organic solvents — overturning the prior assumption that photodepolymerisation of PMMA required chlorinated solvents to stabilise radical intermediates. The team validated the technique on post-consumer specimens including tinted automotive tail-lights and signage, and repolymerised the recovered monomer into pristine acrylic sheet.
"This funding allows us to expand our approach from a laboratory breakthrough into a more comprehensive, scalable solution," Dr Freakley said. "By combining expertise across disciplines, we can address the full lifecycle of acrylic materials and move closer to truly circular use." Dr Husband was blunter about the task: "Acrylic plastics are widely used but challenging to recycle efficiently. This project gives us the platform to develop technologies that could significantly reduce waste and unlock long-term sustainability benefits."
At the funder level, Dr Kedar Pandya, Executive Director for Strategy at EPSRC, framed the award inside UKRI's wider waste-systems agenda: "By funding ambitious, collaborative and impactful research into recycling technologies, we are helping to tackle some of the most complex challenges in our waste system from collection through to currently hard-to-recycle material recovery."
What happens next?
The timeline is staged. Months one to six cover personnel onboarding, commissioning pilot continuous photochemical reactors at the ISCC and sourcing commercial PMMA waste feedstocks. Months seven to 18 target continuous monomer throughput above 100 grams per hour, with solvent recycling loops optimised to 98% internal recovery. Interim stage-gate reviews by Defra and EPSRC will assess process energetics and repolymerisation quality before any move toward commercial demonstration.
Trade coverage has already flagged the strategic case: high embedded economic value makes PMMA a strong candidate for chemical recovery, and domestic monomer production would insulate UK manufacturing from raw-material supply shocks. Regulatory analysis from the Chartered Institute of Environmental Health noted that keeping depolymerisation below 200°C eliminates hazardous cracking emissions, aligning the process with clean-air objectives.
The verdict arrives at the stage gates: exceed 100 grams per hour, hold 98% solvent recovery, and the project earns its march toward demonstration.
via casrai.org (Source)
More from Olivia Hart
Show full bio
Staff writer covering regulation, policy and their impact on Circular economy and the environmental industry at Circular Wire.
557 articles