Industrial Decarbonization

Silver paste hit 30% of solar cell cost, UNSW pushes substitutes

Silver paste reached up to 30% of cell manufacturing cost at early-2026 price peaks. UNSW teams report nickel and aluminum contacts closing the efficiency gap.

Why Solar Researchers are Working to Devise a Silver Reduction Playbook
Why Solar Researchers are Working to Devise a Silver Reduction Playbookgerhardt12 / pixabay

Waypoints

  1. Silver paste accounted for up to 30% of solar cell manufacturing cost at early-2026 price peaks

  2. Aluminum rear contacts in TOPCon cells achieved 22.9% efficiency vs 23.7% for silver references

  3. Replacing 10% of silver powder with nickel cut rear-finger raw-metal costs 6.8% with only 0.024 percentage-point efficiency loss

  4. Solar panels must operate reliably outdoors for 25 to 30 years, and outdoor test data for alternative contacts is not yet available

Silver paste accounted for up to 30% of solar cell manufacturing cost when silver prices peaked in early 2026, according to industry analysts — and that number is now driving a coordinated research push at UNSW Sydney to cut or eliminate the metal from PV contacts.

Dr Ning Song, Senior Lecturer in UNSW's School of Photovoltaic and Renewable Energy Engineering, is leading the work alongside Scientia Professor Martin Green. Their mandate is narrow and material-specific: find metallization routes that preserve cell efficiency while shrinking the silver line item.

Why the metal stream matters

Silicon solar cells generate electricity when sunlight strikes them, but that current has to be collected and carried out of the cell. Extremely thin printed metal lines, called contacts, do the job. Silver dominates because it conducts exceptionally well and screen-prints into fine fingers with minimal shading of the cell.

"Silver is used for the metal contacts that get the current out of the solar cells," Dr Song said. "It has very good conductivity and is easy to screen print. So silver has been one of the best for performance, but not necessarily moving forward for cost and sustainability."

The cost share varies with cell technology, silver prices and paste consumption. But with prices volatile, the exposure is structural: solar may be among the cheapest sources of renewable electricity, yet each cell carries a precious-metal dependency on a finite, contested resource also demanded by electronics and other industries. Mining and processing silver carry their own energy, land-disturbance and waste burdens.

What does the alternatives pipeline look like?

Three candidate metals are in play, each with a distinct defect profile:

  • Aluminum — significantly cheaper, already used in established metallization processes, but less conductive than silver. Contact interfaces and firing conditions must be tightly controlled to avoid electrical losses.
  • Copper — cheap and nearly as conductive as silver, but it diffuses into silicon and interferes with cell operation, and it oxidizes. Silver-coated copper particles are one workaround.
  • Nickel — stable with an established semiconductor track record, but prone to contact losses and printability issues.

For aluminum, the UNSW team is tuning paste recipes and firing conditions. "We are trying to reduce these losses by tuning the aluminum paste recipe and optimizing the firing conditions," Dr Song said. A separate study produced an aluminum paste that reduces silver use and simplifies manufacturing for advanced back-contact cells. In industrially relevant TOPCon cells, the group demonstrated aluminum rear contacts reaching 22.9% efficiency against 23.7% for silver-contact references — a workable gap, but a gap nonetheless.

Where does nickel stand?

The most quantified result comes from a recent study in Solar Energy Materials and Solar Cells, from Dr Song's team including PhD researcher Lizhi Sun and Professor Green. Replacing 10% of the silver powder by weight with a suitable nickel powder in the rear contacts of industrial TOPCon cells cut rear-finger raw-metal costs by 6.8% at an absolute efficiency loss of just 0.024 percentage points.

The catch: higher nickel content increased paste consumption, largely offsetting the expected savings. "Replacing silver with nickel is not simply about using a cheaper metal," Dr Song said. "We need to consider how the nickel powder affects electrical contact performance, printability and the amount of paste consumed during manufacturing."

She frames the broader effort as a joint one: academia supplies fundamental mechanisms and new materials, industry brings manufacturing expertise and scale.

What decides the timeline?

Reliability certification does. Panels must run outdoors for roughly 25 to 30 years, and manufacturers need field data that laboratory testing cannot substitute for.

"Although other options may have passed testing in the lab, industry still needs confidence from outdoor testing and that data may not yet be available," Dr Song said. "We have to make sure the modules are reliable over the long term so they can work efficiently for many years."

There is no single winner — suitability depends entirely on cell structure. Dr Song expects sustained research with industry partners to deliver substantial silver reductions, and possibly silver-free contacts in selected cell technologies, over the coming years. Outdoor exposure data is the milestone that sets the pace.

via azocleantech.com (Source)

Share this article:

More from Elena Vasquez

Elena Vasquez

Show full bio

Senior reporter covering technology and product news in Circular economy and the environmental industry at Circular Wire.

532 articles

Nearby routes

« Previous articleNext article »