Industrial Decarbonization

Single-crystal COF membrane hits 74,800 Barrer in carbon capture study

A Tianjin University-led team has reported a polymer-based membrane with 74,800 Barrer CO2 permeability, 75.5% filler loading, and 85% retention after six months of ageing.

Single-Crystal COF Membranes Shatter Barriers for Cheaper Carbon Capture - Bioengineer.org
Single-Crystal COF Membranes Shatter Barriers for Cheaper Carbon Capture - Bioengineer.orgAI-generated

Waypoints

  1. Tianjin-led team reports CO2 permeability of 74,800 Barrer in a 2026 Nature Energy paper, versus tens to low hundreds of Barrer for commercial polymer membranes.

  2. Single-crystal COFs were loaded into a polyimide matrix at 75.5% by volume, with CO2/N2 selectivity of roughly 20.

  3. Polyimide samples retained approximately 85% of initial permeability after six months of ageing at room temperature.

  4. Co-first authors Hanze Ma and Shilin Guo; corresponding authors Guangwei He and Zhongyi Jiang; collaborators include EPFL and the University of Southern California.

A polymer-based carbon capture membrane with a CO2 permeability of 74,800 Barrer has been reported by a Tianjin University-led team — roughly two to three orders of magnitude above commercial polymer membranes now used in post-combustion service.

The figure appears in a 2026 Nature Energy paper authored by co-first authors Hanze Ma and Shilin Guo, with Guangwei He and Zhongyi Jiang as corresponding authors. Collaborators include EPFL and the University of Southern California. The team embedded single-crystal covalent organic frameworks, or COFs, into a polyimide matrix at loadings of 75.5% by volume.

How does 74,800 Barrer compare with deployed membranes?

Commercial polymer membranes for CO2/N2 separation typically post permeabilities in the tens to low hundreds of Barrer. Higher permeability translates directly into smaller membrane areas and lower driving pressures for a given capture duty, which in turn reduces capital cost and energy draw.

Selectivity held at roughly 20 for CO2 over N2. The authors position the material well past the conventional upper-bound trade-off line that has constrained polymer membrane design for two decades. Previous life-cycle assessments have flagged that membrane separation can compete with amine-based chemical absorption only if materials reach the permeability–selectivity combination that makes module sizes practical.

Why does filler loading decide performance?

Mixed-matrix membranes blend the processability of polymers with the engineered pores of crystalline fillers. Past recipes kept filler fractions low because high loadings trigger aggregation and interfacial defects that collapse selectivity rather than improve it.

The Tianjin group reversed that logic. Rather than maximizing polymer-filler bonding, the researchers tuned competing interaction energies so that single-crystal COFs dispersed uniformly at 75.5% by volume. The COF network, not the polymer, became the continuous transport pathway through which gas molecules travel.

Single-crystal COFs carry an edge over polycrystalline versions. Their defect-minimized lattices preserve the designed pore geometry, so the membrane inherits intact transport channels rather than a degraded approximation. Unlike metal-organic frameworks, COFs contain no metal nodes, making them fully organic and compatible with an organic polymer matrix.

Will the membrane hold up over time?

Polymer membranes densify over months and years, a process called physical ageing that steadily throttles gas flow. The team aged polyimide-based samples at room temperature for six months. The samples retained roughly 85% of their initial permeability, a result the authors attribute to the rigid crystalline network stabilizing the polymer against densification.

For a material operating at such extreme filler loadings, six-month stability is itself a notable finding.

What still has to be proven?

The study is a laboratory demonstration. The authors frame solution processability as a design requirement and note that the all-organic formulation fits existing membrane fabrication methods. No exotic deposition step is required.

Translating a laboratory coupon into square meters of defect-free module, then validating performance on real flue gas with humidity, sulfur compounds, and temperature swings, will demand further engineering. The Intergovernmental Panel on Climate Change and the International Energy Agency both classify post-combustion capture as a required tool for limiting warming.

If pilot data confirm the lab numbers, the membranes could narrow the energy and footprint gap between membrane separation and amine-based chemical absorption, the incumbent technology in most post-combustion capture plants.

The authors, including Ma, Guo, He, and Jiang, frame the weak-interaction inlaying strategy as a general route to exploiting the intrinsic properties of porous crystals inside processable membranes. That principle could extend beyond COFs to other crystalline fillers and beyond carbon capture to hydrogen purification and hydrocarbon cracking.

For now, the paper sets a benchmark: a single-crystal COF membrane with six-month stability data, selectivity intact, at a permeability that redraws the polymer membrane map. The next milestone the field will track is the first independent pilot run on real flue gas.

DOI: 10.1038/s41560-026-02149-9

via doi.org (Original)

Share this article:

More from Elena Vasquez

Elena Vasquez

Show full bio

Senior reporter covering technology and product news in Circular economy and the environmental industry at Circular Wire.

532 articles

Nearby routes

« Previous articleNext article »