Recycling Industry
Induction Heating Delaminates PV Modules in Five Seconds
UNSW and KETI researchers delaminated glass-glass PV modules in as little as 5.4 seconds using induction heating, recovering 99.8% of module mass including intact silicon cells.
Waypoints
Induction heating separated modified glass-glass mini-modules in 5.4 seconds at a 200 A coil current.
The process recovered 99.8% of total module mass, including glass, silicon cells and encapsulant.
Heating produced a temperature difference of more than 200 C between cell and glass at 100 A.
Mechanical EVA scraping from glass caused less than 10% encapsulant mass loss.
Findings published in Communications Materials by researchers from UNSW and KETI.
Five seconds. That's how fast an international research team separated the layers of an end-of-life photovoltaic module using induction heating — while recovering 99.8% of the module's original mass, including glass, silicon cells and polymer encapsulant.
The work, published in Communications Materials under the title "Inductive heating for photovoltaic module recycling and near-complete component recovery," comes from scientists at the University of New South Wales (UNSW) in Australia and South Korea's Korea Electronics Technology Institute (KETI). For an industry staring down a rising wave of decommissioned panels, the numbers matter more than the novelty: current delamination methods are slow, thermal or chemical, and they often contaminate or damage the highest-value fraction — the silicon cell.
What does the design change?
The team didn't just build a new process. They redesigned the module itself to come apart.
"We designed a glass-glass photovoltaic module that is easier to take apart at the end of its life," corresponding author Yonghwan Lee told pv magazine. "Using induction heating, we rapidly separated the layers of our test module and recovered 99.8% of its original mass, including the glass, the silicon cell and the polymer encapsulant."
That's the circularity pledge with a deadline attached: near-total material recovery, built into the product at lamination rather than fought over at the recycler's inbound scale. For practitioners, the distinction is real. Most glass-backsheet modules on roofs today were laminated with the assumption that nobody would ever take them apart. A glass-glass architecture designed for delamination flips that assumption.
How the process works
The researchers began with Comsol Multiphysics simulations of induction heating in passivated emitter and rear contact (PERC) cells and heat transfer through surrounding layers. They modelled the effects of:
- operating frequency
- coil current
- coil-to-cell distance
- electrode thickness
They then moved to physical samples: a 2 cm × 2 cm PERC cell laminated onto tempered glass with ethylene vinyl acetate (EVA) encapsulant, rear of the cell left exposed. A water-cooled copper induction coil operating at 270 kHz to 300 kHz rapidly heated the cell's metal contacts, triggering localised EVA decomposition at the cell-encapsulant interface. Samples hung cell-side-down so gravity did part of the work.
The physics paid off. At a coil current of 100 A, induction heating produced a temperature difference of more than 200 C between the cell and the glass — enough to decompose the EVA at the interface while leaving the bulk material largely intact. With gravity-assisted separation, cells detached in roughly 14 seconds.
What came out the other side?
This is where recyclers should pay attention. Microscopy showed no significant polymer residue and no structural damage on recovered cell surfaces. Spectroscopy indicated the remaining EVA largely retained its chemical structure — meaning it could potentially be reprocessed rather than written off as char.
Lee said the team was surprised by how quickly and cleanly the silicon cell separated.
"In our fastest test, the module layers separated in just five seconds. We recovered the cell intact, with no visible polymer residue on its surface, without having to remove the entire encapsulant layer first," he said.
The team then fabricated modified glass-glass mini-modules — a single PERC cell, EVA encapsulant, and two tempered glass sheets measuring 5 cm × 8 cm and 1 mm thick. Polytetrafluoroethylene (PTFE) release films, each with a 1.8 cm × 1.8 cm central opening, sat between cell and EVA on both sides to vent gases generated during heating. The modules hung in a custom support jig while the coil ran at 100 A, 150 A and 200 A.
The separation times tracked the current:
- 18.6 seconds at 100 A
- 8.3 seconds at 150 A
- 5.4 seconds at 200 A
Across the runs, the process recovered 99.8% of total module mass, with negligible losses of glass, cells and release films. Post-delamination, the researchers mechanically scraped residual EVA off the glass, losing less than 10% of the encapsulant mass. Analysis of recovered cells again showed no significant surface residue.
To put the speed in context: a module that comes apart in five seconds, rather than minutes in a hot kiln or hours in a solvent bath, changes the throughput math for a recycling line. It also cuts the energy applied to the glass — the temperature differential does the work where it's needed, at the interface, not across the whole laminate.
What happens next?
The caveat, as always with lab results: these were 2 cm × 2 cm cells and 5 cm × 8 cm mini-modules, not the 1.8-metre commercial panels rolling into recyclers' yards.
"For us, this points to a way to recycle modules quickly and brings the goal of 100% material recovery closer," Lee said. "Our next step is to apply the process to full-size commercial PV panels and scale it up for use in commercial recycling operations."
That scale-up is the milestone to watch. Until induction delamination runs on full-size laminates at line speed, the 99.8% recovery figure belongs to the laboratory — promising, reproducible, and not yet quotable in a recycler's mass balance.
via pv-magazine-australia.com (Source)
More from Elena Vasquez
Show full bio
Senior reporter covering technology and product news in Circular economy and the environmental industry at Circular Wire.
532 articles